Market value as of 16 Nov 2026My garage (0)
Mazda · FD3S · 1993–1995 (US)

Mazda RX-7 FD3S

Sold in the US Sold in Japan as the Efini RX-7 (later Mazda RX-7) through 2002; US and Canada received it for the 1993 to 1995 model years. Compare
Mazda RX-7 FD3S
Photo: Tokumeigakarinoaoshima / Wikimedia Commons / CC0

Mazda took the RX-7 upmarket for its third generation.

Origins and development

The third-generation RX-7 began as a design contest. In 1987 Mazda collected eight scale-model proposals from its Hiroshima and Yokohama studios, a design firm in the United Kingdom and its California studio, then narrowed them to two. The Hiroshima entry was a cab-forward shape that drew on the company’s racing prototypes. The California entry, sketched by Wu-Huang Chin under studio head Tom Matano, won in May 1988 at the opening of Mazda’s research center in Irvine. The interior came from Hiroshima, and chief designer Yoichi Sato refined the concept for production. The shape was largely settled by the end of 1989.

Mazda kept the layout of the car it replaced: two seats, rear-wheel drive and a twin-rotor turbo engine mounted behind the front axle. Matano wanted a design that would age well. The studio kept a 1960s Ferrari 275 GTB/4 on hand as a reference for proportion and surface.

Body and chassis

Mazda chose to make the car wider than Japan’s small-car rules allowed. That decision gave the designers room for wider tires and a lower, more planted stance, but Japanese owners paid higher annual road tax for it. Mazda offered the smaller Eunos Roadster and Eunos Presso to fill the gap.

The car was also lighter than its predecessor. Contemporary reports put the weight loss at 243 lb, with body rigidity up by about 20 percent. Curb weight in the US was roughly 2,800 lb (1,270 kg). Suspension used double wishbones at all four corners, and the US cars came with anti-lock brakes and a limited-slip differential. With the engine set back in the chassis and the weight kept low, the car earned a reputation for balance.

The sequential twin-turbo rotary

The 13B-REW was a 1.3 L two-rotor engine with two turbochargers working in sequence. Mazda developed it with help from Hitachi, and it was the first mass-produced sequential twin-turbo system exported from Japan. The first turbo supplied about 10 psi of boost from around 1,800 rpm. The second joined in near 4,000 rpm, and the changeover finished at about 4,500 rpm. The aim was to give a rotary engine strong response at low revs without the lag of one large turbo.

US cars were rated at 255 hp at 6,500 rpm and 217 lb-ft of torque at 5,000 rpm, with an 8,000 rpm redline. In Japan the output rose from 255 PS at launch to 280 PS by the end of production. The plumbing for the turbo system used many solenoids, actuators and vacuum hoses. The control system is complex, and its parts are prone to failure.

Production and variants

Production began in 1991 and sales in Japan started that December. Total FD output came to 68,589 cars by 2002. Europe received only a small allocation, about 1,152 cars through official channels, of which the UK took 210.

The US market had the car from the 1993 model year through 1995. Roughly 13,879 were sold there, and only about 500 were built as 1995 models before North American sales stopped. US trims included the base car, a Touring package with leather and a sunroof, and the R1, which was renamed R2 for 1994. The R models added stiffer springs, Bilstein shocks, a strut bar, extra oil cooling and a rear wing.

Japan received a wider range under the Efini and later Mazda badges. The lightweight Type RZ arrived in 1992 in a run of 300, with another 150 in 1993. The final special edition, the Spirit R, was built in 1,504 units across three packages: 1,044 Type A, 420 Type B and 40 Type C. A Bathurst R followed in 2001.

What made it special

The FD gave a driver a very light, very balanced two-seat coupe at a time when rivals such as the Mitsubishi 3000GT were far heavier. Motor Trend named it Import Car of the Year for 1993, and Car and Driver placed it on its Ten Best list from 1993 to 1995. Playboy also picked it as its 1993 car of the year.

It raced early and often. The FD made its professional race debut at Miami on February 23, 1992, and won the IMSA Supercar race at Sebring in 1994. In Australia an RX-7 won the Eastern Creek 12 Hour in 1995. The car reached showrooms soon after Mazda’s 1991 win at Le Mans.

Legacy

Slow sales ended the car in the US after 1995. Japan kept building it until 2002, and the FD proved to be the last RX-7. Matano himself has described it as the last car of its kind.

Its reputation has grown through tuning, drifting culture, anime and video games.

Importing and eligibility

Sold new in the US for 1993–95. JDM cars through 2002 are also import-eligible, subject to build date.

Eligibility depends on the individual car and its build date. Check with a licensed importer before you buy.

Leave a Reply

Your email address will not be published. Required fields are marked *